#!/usr/bin/perl

$pi = 3.14159265359;
$fn = 20;

# An eagle "wire" specifies two endpoints, and an optional curvature.
# A curvature requires we calculate a centerpoint for a circle.
# A curvature of zero is implemented as a simple hull around the endpoints.
sub wire {
  local($x1, $y1, $x2, $y2, $curve) = @_;
  $curve = 0 unless defined $curve;
  $curve *= $pi / 180; # Convert to radians
  $width = 0.1;
  if ($curve == 0) {
    print "hull() {\n";
    print "    translate([$x1, $y1, 0]) circle(d=$width);\n";
    print "    translate([$x2, $y2, 0]) circle(d=$width);\n";
    print "}\n\n";
  } else {
    # Some trig to establish the center.
    # Compute the length of the chord.
    $dist = sqrt(($y2-$y1)*($y2-$y1) + ($x2-$x1)*($x2-$x1));
    # Based on the given curve, project on the unit circle.
    # One endpoint of the resultant chord is [1, 0].
    # Find the other endpoint.
    $atan = atan2(($y2-$y1), ($x2-$x1));
    $cos = cos($curve);
    $sin = sin($curve);
    # Now, what is the length of the chord on the unit circle?
    $udist = sqrt(($sin*$sin) + ($cos-1)*($cos-1));
    # Their ratio is the desired radius.
    # (r should be 9.525 in the example.)
    $r = $dist / $udist;
#print "r = $r\n";
# At this point, $atan has the angle from [x1, y1] to [x2, y2].
# To that, we must add (180-abs($curve))/2 to point to the center.
# Note that the sign of $curve and of our addend should be the same.
    # Now, get the rise and run of the angle formed by the chord
    # and a line from [x1, y2] to the center point.
    $a = ($pi - abs($curve)) / 2;
    $a = -$a if $curve < 0;
    $a += $atan;
    $rise = sin($a) * $r;
    $run  = cos($a) * $r;
#print "run, rise = ", cos($a), " ", sin($a), "\n";
# BUGBUG: $rise and $run must be sign adjusted for quadrant!
    # Calculate the center point for the arc.
#print "[x1, y1] + [run, rise] == [$x1, $y1] + [$run, $rise]\n";
    $x = $x1 + $run;
    $y = $y1 + $rise;
#print "center: [$x, $y]\n\n";
    # We finally know the radius and center of the arc
    # so we can render it. Start with the endpoints.
    print "translate([$x1, $y1, 0]) circle(d=$width);\n";
    print "translate([$x2, $y2, 0]) circle(d=$width);\n";
    # Render the outer circle, then subtract the inner circle
    # and the masking polygon.
    print "difference() {\n";
    print "    translate([$x, $y, 0]) circle(r=$r+$width/2);\n";
    print "    translate([$x, $y, 0]) circle(r=$r-$width/2);\n";
# TODO: Masking polygon
    print "}\n\n";
  }
}

&wire(9.525, 0, 463.55, 0);
&wire(471.4875, 7.9375, 471.4875, 76.2);
&wire(461.9625, 85.725, 9.525, 85.725);
&wire(0, 76.2, 0, 9.525);

&wire(0, 76.2, 9.525, 85.725, -90);

&wire(9.525, 0, 0, 9.525, -90);
&wire(471.4875, 7.9375, 463.55, 0, -90);
&wire(461.9625, 85.725, 471.4875, 76.2, -90);