Frames for Sheet and Layout Date: >LAST_DATE_TIME Sheet: >SHEET REV: TITLE: Document Number: >DRAWING_NAME FRAME B Size , 11 x 17 INCH, Landscape DEC Flip-Chips Vincent R. Slyngstad vrs@msn.com One-wide female edge connector V U T S R P N M L K J H F E D C B A 1 2 2 1 >Name >Name Two-wide Female Edge Connector V U T S R P N M L K J H F E D C B A 1 2 2 1 >Name >Name >Name 2 1 >Name 2 1 A B C D V U S P M K E H F J L N R T V U T S R P N M L K J H F E D C B A 1 2 2 1 >Name >Name >Name 2 1 >Name 2 1 A B C D V U S P M K E H F J L N R T 2 1 V U T S R P N M L K J H F E D C B A 1 2 2 1 >Name >Name >Name 2 1 >Name 2 1 A B C D V U S P M K E H F J L N R T One-wide female edge connector, 18 pin V U T S R P N M L K J H F E D C B A >Name >Name One-wide female edge connector, Side 2 only V U T S R P N M L K J H F E D C B A 1 2 2 1 >Name >Name V U T S R P N M L K J H F E D C B A 1 2 2 1 >Name >Name V U T S R P N M L K J H F E D C B A 1 2 2 1 >Name >Name >Part VCC GND GND >Part >Value >Part >Part >Value A pull-up. +3V +5V >Part >Value >Part >Value D C 1 0 S R >Part >Value D 1 0 C S R >Part K2 >Value >Part D 1 0 C S R A1 >Value >Part >Value .05us .15us .25us .35us .45us .0us .1us .2us .3us .4us .5us >Part >Value >Part >Value >Part >Part >Value -15V >Part >Part >Value >Part >Value Sixteen inverters. 10 2-input NAND Gates 6 4-input NAND Power Amplifier Two sets of 3 D flip-flops Tapped Delay Line Double sided Double Height Connector, 72 pins 6 4-input NAND Gates 6 Dual Bus Drivers Empty Slot Two-sided Posibus cable/connector. 6 2-2 AND-NOR Gates 8 3-input NAND Gates One-sided 18 pin connector/cable. Supply Symbols GND, VCC, 0V, +5V, -5V, etc. Please keep in mind, that these devices are necessary for the automatic wiring of the supply signals. The pin name defined in the symbol is identical to the net which is to be wired automatically. In this library the device names are the same as the pin names of the symbols, therefore the correct signal names appear next to the supply symbols in the schematic. <author>Created by librarian@cadsoft.de</author> >VALUE >VALUE >VALUE >VALUE SUPPLY SYMBOL SUPPLY SYMBOL SUPPLY SYMBOL SUPPLY SYMBOL D-BS-BM8-L-03 Control Timing A When installing additional memory fields, move jumpers K2, P2, and U2 to enable BEMA when ** highest available field is selected. To protect field Jumper pins K2 P2 U2 1 2 3 4 5 6 7 L2 L2 L2 J2 J2 J2 J2 R2 R2 R2 N2 N2 N2 N2 T2 T2 T2 T2 V2 V2 V2 To install on 8/L with existing MC8/LA memory, change E2-D2 jumper to E2-F2. *** ** *** (350) * These circuits are wired to common substrates for temperature tracking. * * * * * (550) Empty Slots: D-BS-BM8-L-04 Control Gating A D-BS-BM8-L-05 Field Registers A D-BS-BM8-L-06 MD Buffer A D-BS-BM8-L-07 MA, MB Buffers, Switches and Indicators A M8328 ABCD01 D-BS-BM8-L-08 Expanded Omnibus 8E Memory A Note: Cxx connector used only on front panel. ABCD02 ABCD03 ABCD04 ABCD05 ABCD06 ABCD07 ABCD02 ABCD03 ABCD04 ABCD05 ABCD06 ABCD07 D-BS-BM8-L-09 Memory Cables to/from MC8-LA A A1, C1, F1, K1, N1, R1, and T1 are grounded on all connectors on this page. PDP-8L slot B34 MC8-LA slot A29 PDP-8L slot B35 MC8-LA slot A30 PDP-8L slot B36 MC8-LA slot A31 D-BS-BM8-L-10 I/O Connectors, Positive Bus A A1, C1, F1, K1, N1, R1, and T1 are grounded on all connectors on this page. PDP-8L slot D36 MC8-LA slot A36 PDP-8L slot D35 MC8-LA slot A35 PDP-8L slot D34 MC8-LA slot A34 PDP-8L slot C36 MC8-LA slot A33 PDP-8L slot C35 MC8-LA slot A32